Computers have many functions and provide us with amazing conveniences, which we could not even imagine before. Everyone knows HP computers! The best computers of this brand are laptops. HP notebooks civilized the computer market with their ultra-thin bodies. The ultra-thin body is a big benefit, but it also brings a lot of inconvenience to disassembly, so the disassembly project of HP notebooks is larger than that of other brands. The following editor uses HP Compaq v3000 as an example. Please introduce it in detail!
HP Compaq v3000 disassembly preparation tool.
In fact, it is quite simple. You don’t need too many screwdrivers. It is enough to disassemble the machine with ph1 and ph0. In addition, you need to disassemble the pick. Some people use phone cards and fingernails, but I don’t think it is as useful as this. I also need a tweezers and a brush.
Detailed disassembly steps of HP Compaq v3000
1. Remove the back cover
There is no battery installed on the machine. The girl was afraid of the weight, so she removed the battery, but It is better to bring a battery. In case of power outage or something, you can protect the machine and the files you are working on. The back cover is still relatively easy. I think it won’t be a problem for everyone. You can remove the three back covers by unscrewing the nails marked above.
2. Remove the wireless network card and hard disk
Unscrew the nail, pull up the aluminum foil at the arrow position, and the hard disk will come out; the same is true for the wireless network card. First unplug the antenna, unscrew the screws, and then remove the network card.
3. Remove the body screws
The 12 screws are all fixing screws for fixing the CD case, the three marked in yellow The screws are for fixing the touch bar, and the three screws marked in green are for fixing the keyboard. Remove all 18 screws above. I don’t know about three more blue ones.What is it used for? It's under the hard drive and has been removed just in case.
4. Remove the keyboard and pressure strip
Here you need to remove the keyboard first and then the pressure strip! Because there are two interfaces on the pressure strip under the keyboard. When disassembling the keyboard, be careful to pull it up a little and then pull it toward the screen, because the four sockets on the keyboard near the palm rest are relatively long, and if you pull them apart directly, they may become distorted. In addition, be careful not to pull it too far. Just loosen the keyboard. Then remove the cable and the keyboard will come off.
5. Remove the optical drive
The next step is to remove the optical drive. You will see a hole on the touch panel. Use a screwdriver to insert it and pull it to the right to remove the optical drive. Finally, there are marks on the right side and the touch panel. The screw on the right is the screw that fixes the C case. Unscrew it, and then you will see the touch panel cable. Remove it. If it is not convenient to disassemble, you can disassemble it. Remove the CD case when it is a little longer, but be careful not to break it.
6. Disassemble the CD case (and memory)
Unscrew the two screws and the CD case can be disassembled . When disassembling, you can use a pick to slide along the gap in the CD case, and the two cases can be easily disassembled. The green arrow marks the method of disassembling the memory. I think everyone should know this. In fact, it does not need to be disassembled here, and it will not affect the disassembly at all.
7. Remove the motherboard from the D case
Next you will see a more complicated scene. When I dismantle it here, I feel a little confused about where to start. In fact, it’s not too complicated, just take it apart one by one. First, pull up the speaker. The wire is stuck to the motherboard. Slowly tear it off. You will find an excuse marked by a yellow circle in the middle. Pull it out. Then there are two more interfaces. They are a bit big and a bit It's not easy to pull out. You can use a screwdriver to lift it, but be careful not to damage the interface. The upper one of these two interfaces is connected to the speaker, and the lower one is connected to the USB interface on the right side.
8. Remove the heat sink and fan
The heat sink and fan here are integrated. It should be said that they were like this before they were removed from the motherboard. Unplug the fan's power socket and remove the heat sink. It's actually quite simple. You just need to unscrew the four screws. But be careful to keep the position of the heat sink as balanced as possible. Don't knock off a corner of the U with force, which will cause a cup. It’s ready.
9. Clean the fan and heat sink
After removing it, it was found that the fan was actuallyIt can be removed. Unscrew the three screws on the top and the fan will come down. Use a brush to clean the dust on the fan blades, as well as the dust on the heat dissipation fins. It is because they are blocked there that the heat cannot be blown out. Clean them thoroughly. Use tweezers to remove any corners that cannot be brushed. , brush again, and blow it well, it should be almost done.
The HP Compaq v3000 is a representative model of HP notebooks, so everyone must remember it. Of course, the editor is just introducing it to you. The editor has not yet had time to give you a detailed introduction to the disassembly method of this computer and its specific configuration. If you are interested, you can learn more in detail. The editor recommends that you go to HP's official computer website, because the introduction on the official website is authoritative after all and allows you to get official data. However, the editor wants to tell you that this computer has been discontinued, so it is difficult to find data on it.